How To Repair Dishwasher Drain Hose
How to replace a dishwasher drain hose
By Lyle Weischwill
This dishwasher repair guide shows how to replace the drain hose that connects the drain pump to the drain line that carries water to the sink bleed. If the bleed hose leaks, remove it and replace it with a manufacturer-approved replacement role. This process is for Kenmore, Whirlpool, KitchenAid, Maytag, JennAir and Amana dishwashers. You too can utilise the same bones steps to replace the drain hose in some GE, Frigidaire, Electrolux and Samsung dishwashers.
Instructions
-
01.
Shut off electrical ability and h2o supply to the dishwasher
Flip the house circuit breaker switch to the Off position to completely disconnect electrical power to the dishwasher (some older homes instead have a fuse that yous remove from the fuse box). To verify that power is asunder, brand sure the display on the control panel can't be activated.
Find the water supply valve for the dishwasher under the sink (or in the basement). Close the valve to shut off the water supply going to the dishwasher.
-
02.
Remove the bottom front access console and toe panel
Using a one/4-inch nut driver, remove the screws that hold the front access panel in place. Pull the admission panel and the toe panel forwards, remove them and fix them bated.
Tip: Refer to your installation manual for more details on removing the bottom forepart access panel and the toe panel, if necessary.
Photo: Remove the bottom front access console screws.
-
03.
Pull out the dishwasher
The junction box is at the front of the dishwasher just behind the bottom forepart access panel. Remove the cover on the junction box and disconnect the wires.
Remove the 2 mounting screws from the brackets that secure the dishwasher in the cabinet opening.
Pull the dishwasher out from under the counter. You should have plenty slack in the water supply line and the drain hose to pull the dishwasher in front of the counter opening for the dishwasher.
Tip: You might accept enough slack in the electrical supply wiring and so that yous can pull out the dishwasher without disconnecting the wires.
PHOTO: Remove the junction box cover.
PHOTO: Disconnect the wires.
-
04.
Disconnect the drain hose from the drain pump
Reach under the dishwasher and squeeze the wire hose clench that holds the bleed hose to the drain pump—use pliers if necessary. Pull the end of the drain hose off of the drain pump.
Tip: Place a towel under the drain pump to absorb water from the drain hose.
PHOTO: Release the bleed hose spring clamp.
PHOTO: Disconnect the hose from the bleed pump.
-
05.
Remove the drain hose from the water inlet assembly
From the inside of the dishwasher tub, use a pair of aqueduct lock pliers to remove the plastic nut that secures the water inlet associates.
The h2o inlet associates secures the drain hose to the exterior left panel of the dishwasher tub. Pull out the h2o inlet associates to release the drain hose from the bracket.
Photo: Loosen the plastic water inlet nut.
PHOTO: Remove the plastic water inlet nut.
Photo: Release the drain hose from the water inlet.
-
06.
Disconnect the drain hose from the drain line to the sink
Divide the drain hose that goes to the kitchen sink drain from the dishwasher drain hose that extends to the drain pump.
Pull the drain hose from under the dishwasher and discard information technology.
Tip: If needed, utilise pliers to clasp the wire clench to remove the bleed hose.
Photograph: Disconnect the drain hose.
PHOTO: Pull out the dishwasher bleed hose.
-
07.
Connect the new drain hose
Attach the new dishwasher drain hose to the drain pump, advisedly working the hose onto the drain pump outlet and onto the connexion so it seats properly and does not leak. Secure it with the wire hose clamp.
Road the new drain hose through the water inlet bracket the same style the original drain hose was routed.
Reconnect the portion of the drain hose that goes to the kitchen sink drain to your newly installed drain hose. Make certain that the connection is secure.
Tip: The new bleed hose fits tightly on the drain pump. It ordinarily requires meaning force to work the bleed hose onto the drain pump outlet.
Photo: Connect the hose to the pump.
PHOTO: Route the bleed hose through the water inlet.
-
08.
Reinstall the h2o inlet bracket
Position the water inlet bracket on the side of the tub so y'all can screw the plastic nut onto the bracket from the inside of the tub.
Carefully screw the plastic nut onto the water inlet from the inside of the tub. Hand tighten the nut and and then advisedly tighten it another one/4 turn to seal the inlet.
Tip: Don't overtighten the nut, because y'all could crack the plastic nut or the tub.
Photo: Tighten the plastic nut.
-
09.
Reinstall the dishwasher
Advisedly push button the dishwasher dorsum under the counter. Reconnect the wires in the junction box and reinstall the junction box cover. Replace the bottom front access panel and toe panel.
Insert the screws into the mounting brackets that secure the dishwasher in the counter and tighten the screws.
Position the toe panel on the dishwasher so position the access panel in front of the toe panel. Insert the mounting screws and tighten the screws firmly.
Tip: Refer to the dishwasher's installation guide for additional guidance.
-
x.
Restore the water supply and electrical power
Open up the water supply valve to restore the water supply to the dishwasher. Reset the house circuit breaker to restore electrical ability.
Alarm: Undertaking repairs to appliances can exist chancy. Utilise the proper tools and safety equipment noted in the guide and follow all instructions. Do not keep until you are confident that you lot sympathise all of the steps and are capable of completing the repair. Some repairs should only be performed by a qualified technician.
Symptoms common to all dishwashers
Cull a symptom to come across related dishwasher repairs.
Repair guides common to all dishwashers
These step-past-step repair guides will help you safely gear up what's broken on your dishwasher.
If the dishwasher door doesn't click shut, a cleaved door latch is a likely cause. Follow these instructions to replace information technology yourself.
The user interface control houses the pick buttons and brandish. If it fails, you can't select the cycle and settings. Follow these instructions to supplant information technology yourself.
A completely dead control panel frequently indicates that the thermal fuse on the electronic command board is diddled; follow these steps to supplant a blown thermal fuse in your dishwasher.
Articles and videos common to all dishwashers
Use the advice and tips in these articles and videos to become the most out of your dishwasher.
Parts & More
Bottom-Mount Refrigerator
Chest Freezer
Countertop Microwave
Dishwasher
Dryer
Front-Engine Lawn Tractor
Gas Range
Gas Snowblower
Lawn Sweeper
Microwave
Parts
Range
Side-By-Side Fridge
Boob tube
Washer
Source: https://www.searspartsdirect.com/diy/repair-guide/how-to-replace-a-dishwasher-drain-hose
0 Response to "How To Repair Dishwasher Drain Hose"
Post a Comment